Two sim-cards and GSM-antenna. Ethernet and radio as an option.
Built-in power supply unit from the network: 1.5 A, 12 V.
Accommodates the battery 7.2 A*h.
8 (16) wired security zones.
2 wire fire zones.
7 discrete outputs.
Up to 31 wireless devices.
258 x 295 x 81 mm.
Nord GSM in the metal housing and Nord GSM in the plastic housing have the same board, therefore, in many respects these panels are similar. All the difference is in size and material of the housing:
In a large housing there is a place for the battery of a much larger size — 7.2 A*h. This means that power is enough for more wired sensors.
Do not spoil the view on the wall of office or apartment, can be built into the ATM.
The metal housing allows the use of a radio channel to deliver messages to security console using TP-100-H Low and High radio transmitters and VHF radio antenna.
Nord GSM Metal
In a large metal housing it is more convenient to connect wired zones to terminals. To accurately drill the fixing holes in the wall - there is a tracing paper.
The engineer connects the laptop to the Nord via USB
and configures device communication with console, partitions, users, sensors and other parameters of the alarm system. Engineer configures Nord with a special soft, we call it Hubble.
The feature of Hubble's work is that the engineer first creates a configuration device, and only then records to the device. Therefore, the configurator works quickly, reacting at lightning speed to engineer actions.
For typical sites, you can save configuration and record it on the device without wasting time on individual setting.
The configurator has an interface of devices' settings, it is called the status panel. Engineer sees number of zone, state and error signal level for each device.
Engineer tests both sim-cards: GPRS, CSD, voice channel and SMS.
App lets activate or desactivates any channel for testing.
Practically any mechanism can be controlled remotely: turn on / off the boiler, open the gate, switch on the light and much more.
For Nord GSM there is all necessary equipment for installation of security and fire alarm system.
Nord GSM will allow you to deploy a wireless (up to 31 devices) and a wired (up to 16 zones) security and fire system at the site.
Remote wired keypad K14-LED and wireless CN-Keypad.
Wireless CN-KeyFob with panic button.
TM-keys and RFID-marks
MyAlarm App, iOS / Android.
With expander EW-12 the number of Nord GSM wiring zones can be increased from 8 to 16.
With EF-2 from two security zones it is possible to make two fire zones for connecting two-wire fire detectors.
If the site is large or the signal does not pass through the walls, the wireless repeaters CN-Repeater will help improve the radio communication between the sensor and the panel.
You can use wired and wireless sensors at the same time.
In an emergency situation
user can disarm the site with the code under forcing. In that case the panel will send to the console an event «Disarming under forcing».
An engineer remotely connects to the Nord panel through the web interface of C.Nord Cloud and configures it with a Hubble configurator. The engineer configures the panel the same way as if he connects via USB.
The panel configuration is stored on the device and in the cloud. Therefore, even if you have a bad connection with the device, Hubble will load up immediately (from the cloud) and the engineer starts to work at once.
The same is with the saving of settings. If connection is bad, the engineer does not have to wait: the new configuration immediately will be written into the cloud, and the cloud controls that this configuration will go to the device.
An engineer cannot connect to the control panel without permission. When it is necessary maintenance, an operator of the Security Center gives the engineer permission for remote access to a site for restricted time.
We constantly refine our solutions: we produce new sensors, update the interface of the configurator, etc. For compatibility sometimes it is necessary to update the firmware of the control panel and other devices.
In the case of Nord panel, an engineer will not have to visit the site — he can updated the firmware remotely. Moreover, the engineer can update the firmware immediately on all or several devices and monitor the progress of the update.
1) You can switch off the reset configuration of control panel to the factory settings, and for access to configurator set a complex
If an engineer from a competing firm connected to the device via USB, he can't enter the configurator without the password.
2) You can connect the panel to your console.
The address for connecting to the console is recorded in the internal memory of the processor and remains there even when the configuration is reset.
Even if the attackers break up panel, it will have time to send the event «Probable alarm» to the security console.
Installers put the control panel with a keypad at the entrance on the site, so that customers can conveniently enter the disarming code while there is a delay in the entrance.
We added the event "Probable alarm" (E138) to prevent inference panel fail during the "entry delay". It means, that if after a probable alarm from the site he disarming event will not come, then the console will form an alarm event.
Nords are working with one of the best professional consoles in Russia — Security Center.
Security Center, Duty operator window.
Personal account for client of private security company and app to control security system.
You, as a security company, decide which events are on the custom event timeline in app: armings and disarmings, alarms of security sensors and alarms of utility sensors, operator actions during the alarm processing, reports of rapid-response groups.
— Authorization by phone number and SMS-code;
— entrance by pin-code and fingerprint (Touch ID);
— push-notification of events;
— balance of the personal account (soon);
— armings and disarmings , control of automation.
We output the readings of the temperature sensors on the screen of app.
Adjust the thresholds: then
with temperature changes above or below the threshold you will receive notifications.
You can open the gate,
switch on heating, light and much more directly from the app.
You can connect smoke detectors and water leak sensors to the North GSM Air.
In case of triggering of sensors you will receive notifications until do not react.
We voiced all the push-
notifications by Rita's voice. You definitely do not miss an important event among notifications on your phone.
The button is connected to the site, but you can press it from the app.
You can provide this service to your customers without installing an additional equipment.